KIRBY ELECTRIC INCORPORATED

Use existing Attic Fan circuit to tie in Fire alarm relay, contactor, Jbox. Fire alarm done by others. · Electrical

Construction of a 7 story multi family building including electrical, Fire alarm & 2-way communication wiring, entry intercom, access control, CCTV, and security & panic systems [10/30/26 BGO - Approved Plan Set] · Electrical

wiring for thermostat locations · Electrical

Adding 100A Temp service panel fed from EV panel, Furnish and install (5) 50 Amp whips from temp panel. · Electrical

Adjusting and adding lighting, and replace receptacles with GFCIs in pit and mechanical room. Adjust disconnect and repower elevator controller. · Electrical

200A Overhead Temp. Service to support job trailer and spider boxes during the course of construction for Terminal One Motor and Yacht Club · Electrical

Modernization of elevator and mechanical room. Replace disconnect and connections to elevator controller. Add vapor tight lights in mechanical room and pit. Add power for Mini split. Add sub panel in mech room. Adjust circuits in mechanical room to new sub panel. Replace receptacles with GFCI. · Electrical

Electrical buildout of a multi family building including adding a 1,600A service, receptacles, lighting, access control cabling, CCTV cabling, and telecom cabling. [9/18/26 BGO - Approved Plan Set for electrical and data - note: ERRCS, Access Control, Fire Alarm, 2-Way communication for first responder all require separate permits] · Electrical

Add (2) 120v 20amp circuits with switch disconnects for elevator oil coolers · Electrical

Install one 120v quad cord drop on top lab work area from existing circuit. Install conduit and wire for dedicated Nema 6-15R dedicated cord drop on top lab work area from existing circuit. Change current single duplex receptacle to quad receptacle on lower lab work area. · Electrical

Machine room: Replace (1) existing disconnect in machine room with new fusible disconnect including auxiliary Location of disconnect to remain Refeed controllers from new disconnect, new controller going in, but remaining at 40hp Add power and disconnect for the new split system Provide a 3/4" empty chase for fire alarm Install (4) total j-boxes for fire alarm Remove existing light in machine room and replace with (4) new 4' vapor tight light fixtures Add 1-sub panel with brea · Electrical

Electrical tenant improvement to support installation of new kitchen equipment and associated power distribution within an existing restaurant space. [8-25-26 D Rankin - Assigned contractor, Kirby Electric, updated value, Corrected address. for questions contact Dennis Rishkovoy, 253-457-2173 cell, dennis@kirbyelectric.com] · Electrical

Perform a elevator modernization which consists of, new disconnect to elevator controller, refeed new controller feeding existing 25hp elevator motor, replace existing lights with LED, replace existing receptacles with GFCI. · Electrical

Temp. power permit to support course of construction. During the project we are tasked to furnish and install and electrical system, fire alarm and two way Comm. intercom, Entry intercom, Access control, Telecommunications, and security/panic systems. [8/13/26 BGO - Approved Temp Power Plan Set] [10/26/26 BGO - Approved Revised Service Plan] · Electrical

Perform a elevator modernization which consists of, new disconnect to elevator controller, refeed controller with new upsized wire to accommodate new 7.5hp motor, replace existing lights with LED, add a subpanel into machine room, and power for split unit. · Electrical

Perform a elevator modernization which consists of, new disconnect to elevator controller, refeed controller with new upsized wire to accommodate new 30hp motor, replace existing lights with LED, add a subpanel into machine room, and power for split unit. · Electrical

Using existing sub panel behind paint booth Add 1-90-amp 3P breaker to feed new 15hp compressor Add 1-60-amp 3ph disconnect with fuses Add 1-60-amp 3ph circuit Add 1-120v quad receptacle for dryer and drain Connection to new compressor · Electrical

A new 137 unit, 8-Story Multi-Family Residential Apartment with Underground Parking Garage. Includes (2) 3,000A 120/208V switch boards, and (1) 120/208V 400A LRS. [6/2/26 BGO - Approved Plan Set] · Electrical

Perform an elevator modernization which consists of the following: Equipment room: Replace existing disconnect in machine room with new fusible disconnect Relocate the disconnect location from the west wall to the south wall by door Refeed controller from new disconnect location Replace existing 120v receptacle with new GFCI receptacle Provide a 3/4" empty chase from electrical room to machine room for fire alarm Install (7) j-boxes for fire alarm as per Ryan's directions Provide · Electrical

Provide connection to new 20amp split unit system Provide conduit/wire/disconnect Hook up a 230v 5hp explosion proof vacuum pump Provide connection to vacuum pump control panel, connections from control panel to vacuum pump motor already existing Provide conduit/wire/disconnect · Electrical